Collision protection
- Protection against collisions with the portal support
Modular Cantilever Arms KBG-C
Flexible connection of the SRA overhead crane system up to 85 kg load capacity
With the KBG-C modular cantilever arm, Schmalz is supplementing its product portfolio in the crane systems sector and supplying complete handling solutions from a single source. Customers benefit from a uniform and safe connection of the SRA aluminum overhead crane system. The KBG-C cantilever arm fits perfectly into the overall system.
The proven Schmalz modular system is also used for the KBG modular cantilever arm. The system for the KBG-C modular cantilever consists of just eleven components. These components are combined with each other depending on the customer's application. The special feature: All connecting parts are attached to the section using the same screw set, which simplifies mounting. In addition, only one profile size is used for the entire cantilever system. A separate rolled profile with the corresponding perforations for the screw set was developed for this purpose.
The cantilever variant rounds off the KBG portfolio from Schmalz. The cantilever arms are optimally dimensioned for tube lifter applications with low loads and can be mounted flexibly in the room.
Few components and modular design allow fast processing and short delivery times
Flexible integration into the existing production layout thanks to cantilever arms that can be positioned independently. Easy adaptation for later changes
Easy installation and mounting thanks to the screw set and the intelligent modular system
High level of safety thanks to independent strength calculation of the load-bearing components using the FEM method (designed in accordance with DIN EN 13001; stiffness class: HC3; S class: S3)
Robust surface protection due to the galvanized profile surface
Design
Design
- Self-developed rolled profile (1), 140 x 140 x 4 mm, with perforations for connecting the connecting plates
- Screw set (2) for connecting the components to the section
- Corner plate (3) for connection of the cantilever arms to the pillar
- Foot plate (4) for mounting the pillar to the floor using dynamic dowels
- Suspension plate (5) for attaching the Schmalz aluminum overhead crane system
Modular elements
Modular elements
Portal profile
- In-house developed, hot-dip galvanized rolled profile
- Rasterization in steps of 100 mm
- Used for pillars, cross beams and main beams
- Perforations provide attachment of connecting plates with the screw set
Screw set
- Attachment of all connecting plates to the section
- Simple mounting of the connecting plates on the section
Corner connection
- Connection of pillar and cross beam
- Connection of pillar and main beam at the first and last gate
Foot plate
- Connection to the profile on both sides with two screw sets each
- Orientation of the pillar with adjusting screws
- Anchoring to the floor with two dowels per foot plate
Foot plate
- Foot plate is inserted between the foot plates
- Profile lies flat on the base plate
Suspension plate
- Connection to the profile on both sides with two screw sets each
- Connection of the overhead crane system with standard suspension for I-beams and T-beams (rigid and pendant)
Cover cap
- Cover for the ends of the cross beams
- Visually appealing finish to the section
Cable protection
- Protection of the cable during installation and version in the section
Design Data
Design Data
L = 8000 mm
W = 8600 mm
H = 5160 mm
Maximum load capacity: 85 kg (workpiece weight)
Technical Data
Technical Data
- Maximum dimensions (LxWxH): 30 x 8.5 x 5 m
- Maximum lift capacity: 85 kg (workpiece weight)
- Material: galvanized steel
- Profile cross-section 140 x 140 x 4 mm
Product Inquiry
Accessories
Blower console
- Direct mounting of the blower console on the profile with two screw sets
- The screw sets are included in the set
Product recommendations
Aluminum Bridge Cranes
- Modular crane system for flexible and cost-effective assembly of individual crane solutions
- Installation on ceiling or portal construction
- Particularly suitable for large workspaces
- Lift capacity up to 1,200 kg
Modular Crane Gantries KBG-G
- Maximum dimensions (LxWxH): approx. 30 x 8.5 x 5.5 m
- Maximum load capacity: approx. 500 kg (workpiece weight and weight of lifting device)
- Material: galvanized steel
- Profile cross-section: 140 x 140 x 4 mm