Collision protection
- Protection against collision with the gantry pillar
Modular Crane Gantries KBG-G
Flexible connection of the overhead crane system SRA
With the modular crane gantry KBG-G, Schmalz complements its product portfolio in the field of crane systems and thus supplies complete handling solutions from a single source. Customers benefit from a uniform and safe connection of the aluminum overhead crane system SRA . The crane gantry KBG-G fits perfectly into the overall system.
The proven Schmalz modular system is also used for the modular crane gantry KBG-G. The system for the modular crane gantry KBG-G consists of only twelve components. These components are combined with each other depending on the customer's application. The special feature: All connecting parts are attached to the profile with the same screw set, which simplifies assembly. In addition, only one profile size is used for the entire crane gantry KBG-G. A separate rolled profile with the corresponding holes for the screw set was developed for this purpose.
A Schmalz crane gantry KBG-G consists of at least two gates and can be extended by any number of gates in length. In this way, it can be optimally adapted to the Schmalz aluminum overhead crane system SRA.
Few components and modular design allow fast processing and short delivery times
Flexible integration into the existing production layout and easy adaptation and expansion in case of subsequent changes
Easy installation and mounting thanks to the screw set and the intelligent modular system
High level of safety thanks to independent strength calculation of the load-bearing components using the FEM method (designed in accordance with DIN EN 13001; stiffness class: HC3; S class: S3)
Robust surface protection due to the galvanized profile surface
Design
Design
- Self-developed rolled profile (1), 140 x 140 x 4 mm, with perforations for connecting the connecting plates
- Screw set (2) for connecting the components to the section
- Corner plate (3) for connection of cross beam and main beam (main beam is required for higher lift capacities) on the pillar
- T-sheet (4) for connecting pillar and main beam
- Foot plate (5) for mounting the pillar to the floor using dynamic dowels
Modular elements
Modular elements
Portal profile
- In-house developed, hot dip galvanized rolled profile
- Rastering in steps of 100 mm
- Use for pillars, cross and longitudinal beams
- Perforations provide connection of connecting plates with the screw set
Screw set
- Connection of all connecting plates to the profile
- Simple mounting of the connecting plates on the profile
Corner connection
- Connection of pillar and cross beams
- Connection of pillar and longitudinal beam at the first and last gate
Foot plate
- Connection to the profile on both sides with two screw sets each
- Alignment of the pillar with adjusting screws
- Anchoring to the floor with two plugs per foot plate
Base plate
- Base plate is inserted between the foot plates
- Profile lies flat on the base plate
Suspension plate
- Connection to the profile on both sides with two screw sets each
- Connection of the overhead crane system with standard suspension for I-beams and T-beams (rigid and pendulum)
T-connection plate
- Connection of two longitudinal beams to one pillar
- Connection to the profile on both sides with six screw sets each
Cover cap
- Cover of the ends of the cross beams
- Visually appealing finish of the profile
Cable protection
- Protection of the cable during entry and exit from the profile
Design Data
Design Data
(1) L = max. 8,000 mm
(2) B = max. 8,600 mm
(3) H = max. 5,560 mm
Maximum lift capacity: approx. 500 kg (workpiece weight and weight of lifting device)
Technical Data
Technical Data
- Maximum dimensions (LxWxH): approx. 30 x 8.5 x 5.5 m
- Maximum load capacity: approx. 500 kg (workpiece weight and weight of lifting device)
- Material: galvanized steel
- Profile cross-section: 140 x 140 x 4 mm
Documentation
Documentation
The matching documentation for this product is available in this section.
| Documents | Language |
|---|
Videos
Discover application examples of the product in various industries - user-friendly, informative and practical.
No suitable videos found? Then take a look at our media center. Product Inquiry
Accessories
Blower console
- Direct mounting of the blower console to the profile with two screw sets
- The screw sets are included in the set
Product recommendations
Aluminum Bridge Cranes
- Modular crane system for flexible and cost-effective assembly of individual crane solutions
- Installation on ceiling or portal construction
- Particularly suitable for large workspaces
- Lift capacity up to 1,200 kg
Modular Cantilever Arms KBG-C
- Maximum dimensions (LxWxH): 30 x 8.5 x 5 m
- Maximum lift capacity: 85 kg (workpiece weight)
- Material: galvanized steel
- Profile cross-section 140 x 140 x 4 mm